CORC

在结果中检索

CORC

浏览/检索结果: 共10条，第1-10条 帮助

已选(0)清除 条数/页：   排序方式：
Experimental Study on Spray Etching of Printed Circuit Heat Exchanger Channels 期刊论文
Kung Cheng Je Wu Li Hsueh Pao/Journal of Engineering Thermophysics, 2017, 卷号: 38, 页码: 2674-2678
作者:  Xin, Fei;  Ma, Ting;  Wang, Qiu-Wang
收藏  |  浏览/下载：10/0  |  提交时间：2019/11/26
The optimum synergistic effect of amphiphilic polymers and the stabilization mechanism of a crude oil emulsion 期刊论文
PETROLEUM SCIENCE AND TECHNOLOGY, 2017, 卷号: 35, 页码: 1180-1187
作者:  Kang, Wanli;  Jiang, Jiatong;  Lu, Yao;  Xu, Derong;  Wu, Hairong
收藏  |  浏览/下载：8/0  |  提交时间：2020/01/03
Thermodynamic optimization of a helically coiled heat exchanger for Joule-Thomson refrigerators using response surface methodology 会议论文
作者:  Liu, Xin;  Liu, Yingwen;  Li, Jiapeng;  Chen, Jun
收藏  |  浏览/下载：5/0  |  提交时间：2019/12/02
Experimental optimization of the pem fuel cell performance 期刊论文
Kung Cheng Je Wu Li Hsueh Pao/Journal of Engineering Thermophysics, 2014, 卷号: 35, 期号: [db:dc_citation_issue], 页码: 1826-1830
作者:  Ding, Jing;  Cao, Tao-Feng;  Lin, Hong;  Mu, Yu-Tong;  Tao, Wen-Quan
收藏  |  浏览/下载：2/0  |  提交时间：2019/12/02
Study on Enhanced Heat Transfer and Structural Optimum for Combination Vortex Generator in Spiral Channel 会议论文
3rd International Conference on Civil Engineering and Transportation (ICCET 2013), Kunming, PEOPLES R CHINA, DEC 14-15, 2013
作者:  Qing, Defan*;  Zhang, Yalong;  Liu, Shengxue;  Wang, Cuifang
收藏  |  浏览/下载：4/0  |  提交时间：2019/12/27
Simulation and optimization of capacitance sensor based on orthogonal test 期刊论文
Hsi-An Chiao Tung Ta Hsueh/Journal of Xi'an Jiaotong University, 2013, 卷号: 47, 期号: [db:dc_citation_issue], 页码: 81-86
作者:  Wang, Xiaoxin;  Yan, Jiebing;  Hu, Hongli;  Gao, Xiangxiang;  Zhang, Xiao
收藏  |  浏览/下载：5/0  |  提交时间：2019/12/10
Determination of optimum process parameters in gas-assisted injection molding (EI CONFERENCE) 会议论文
2011 International Conference on Electrical Information and Mechatronics, ICEIM2011, December 23, 2011 - December 25, 2011, Jiaozuo, China
Zi K.; Chen L.
收藏  |  浏览/下载：13/0  |  提交时间：2013/03/25
With finite element analysis software Moldflow  numerical simulation and studies about FM truck roof handle were conducted on gas-assisted injection molding process. The influences of melt pre-injection shot  gas pressure  delay time and melt temperature were observed by using multi-factor orthogonal experimental method. According to the analysis of the factors' impact on evaluation index  the optimized parameter combination is obtained. Therefore the optimization design of technological parameters is done. The results show that during the gas-assisted injection molding  optimum pre-injection shot is 94%  gas pressure is 15MPa  delay time is 0.5s  melt temperature is 240 C. This study provided a more practical approach for the gas-assisted injection molding process optimization.  
Variable sequential combination response surface methodology for press rod system optimization 期刊论文
Hsi-An Chiao Tung Ta Hsueh/Journal of Xi'an Jiaotong University, 2012, 卷号: 46, 期号: [db:dc_citation_issue], 页码: 57-62
作者:  Xie, Jia;  Zhao, Shengdun;  Liang, Jintao;  Ma, Haikuan
收藏  |  浏览/下载：4/0  |  提交时间：2019/12/10
Optimum design of the carbon fiber thin-walled baffle for the space-based camera (EI CONFERENCE) 会议论文
International Symposium on Photoelectronic Detection and Imaging 2011: Space Exploration Technologies and Applications, May 24, 2011 - May 26, 2011, Beijing, China
Yan Y.; Gu S.; An Y.; Jin G.
收藏  |  浏览/下载：12/0  |  提交时间：2013/03/25
The thin-walled baffle design of the space-based camera is an important job in the lightweight space camera research task for its stringent quality requirement and harsh mechanical environment especially for the thin-walled baffle of the carbon fiber design. In the paper  an especially thin-walled baffle of the carbon fiber design process was described and it is sound significant during the other thin-walled baffle design of the space camera. The designer obtained the design margin of the thin-walled baffle that structural stiffness and strength can tolerated belong to its development requirements through the appropriate use of the finite element analysis of the walled parameters influence sensitivity to its structural stiffness and strength. And the designer can determine the better optimization criterion of thin-walled baffle during the geometric parameter optimization process in such guiding principle. It sounds significant during the optimum design of the thin-walled baffle of the space camera. For structural stiffness and strength of the carbon fibers structure which can been designed  the effect of the optimization will be more remarkable though the optional design of the parameters chose. Combination of manufacture process and design requirements the paper completed the thin-walled baffle structure scheme selection and optimized the specific carbon fiber fabrication technology though the FEM optimization  and the processing cost and process cycle are retrenchment/saved effectively in the method. Meanwhile  the weight of the thin-walled baffle reduced significantly in meet the design requirements under the premise of the structure. The engineering prediction had been adopted  and the related result shows that the thin-walled baffle satisfied the space-based camera engineering practical needs very well  its quality reduced about 20%  the final assessment index of the thin-walled baffle were superior to the overall design requirements significantly. The design method is reasonable and efficient to the other thin-walled baffle that mass and work environment requirement is requirement harsh. 2011 SPIE.  
Potential energy surfaces for nucleon exchanging in dinuclear systems 期刊论文
HIGH ENERGY PHYSICS AND NUCLEAR PHYSICS-CHINESE EDITION, 2003, 卷号: 27, 期号: 146, 页码: 48-52
作者:  Zhao, EG;  Li, JF;  Xu, HS;  Li, WF;  Zuo, W
收藏  |  浏览/下载：8/0  |  提交时间：2010/10/29

©版权所有 ©2017 CSpace - Powered by CSpace