CORC

在结果中检索

CORC

浏览/检索结果: 共7条，第1-7条 帮助

已选(0)清除 条数/页：   排序方式：
Material removal behavior in processing green Al2O3 ceramics based on scratch and edge-indentation tests 期刊论文
CERAMICS INTERNATIONAL, 2019, 卷号: 45, 期号: 9, 页码: 12495-12508
作者:  Liu, Yayun;  Deng, Jianxin;  Yue, Hongzhi;  Duan, Ran;  Li, Xuemu
收藏  |  浏览/下载：3/0  |  提交时间：2019/12/11
Effects of Chemical Properties and Roughness on Anisotropic Wetting Observed on Machined Surfaces 期刊论文
MATERIALS TRANSACTIONS, 2015, 卷号: 56, 页码: 149-153
作者:  Shu Liming;  Liang Yande;  He Fuben;  Zhang Hongzhe
收藏  |  浏览/下载：2/0  |  提交时间：2019/12/09
Anisotropic wetting characteristics versus roughness on machined surfaces of hydrophilic and hydrophobic materials 期刊论文
APPLIED SURFACE SCIENCE, 2015, 卷号: 331, 页码: 41-49
作者:  Liang, Yande;  Shu, Liming;  Natsu, Wataru;  He, Fuben
收藏  |  浏览/下载：2/0  |  提交时间：2019/12/09
The NC processing of the transitional region of free surface based on section method 会议论文
Zhengzhou, China, December 8, 2011 - December 10, 2011
作者:  Wu, Zaixin;  Li, Te;  Wang, Yazhou;  Hu, Chibing
收藏  |  浏览/下载：1/0  |  提交时间：2020/11/15
Manufacturing and testing of the line-array fiber-optic image slicer based on silicon V-grooves (EI CONFERENCE) 会议论文
MEMS/MOEMS Technologies and Applications III, November 12, 2007 - November 14, 2007, Beijing, China
Liang J.; Guo P.; Liang Z.; Zhu Y.; Hou F.; Yao J.
收藏  |  浏览/下载：15/0  |  提交时间：2013/03/25
Linear fiber-optic image slicer is used more and more in spatial exploration and imaging system. In this paper  a plane arranging method of fiber-optic array based on Si-V grooves is established in order to improve the accuracy and reduce the cost of manufacturing. Firstly  the Si-V groove array is micro-machined with anisotropic etching process  then optical fibers are placed in the grooves orderly with plane arranging method. Secondly  the end surfaces of the device are polished  also the linear fiber-optic image slicer is packaged. Finally  some parameters are tested  including structure parameters  transmittivity and vibration test. Experimental results indicate that the maximum error accumulated in 2000 periods of the Si-V grooves is 0.5 m  the error of the height in Si-V grooves is less than 0.15m  the roughness of the end surface is less than 0.9nm. The transmittivity of the linear fiber-optic image slicer that without optical film is 51.46% at the wavelength of 632.8nm. After random vibration experiment  the ratio of the broken fiber increased by 0.1%. While the temperature reached 320C  the stress of epoxy will be 130Mpa  which is close to the limit resistance stress of 139Mpa  some cracks appeared.  
A microstructural investigation of the surface of a drilled hole in carbon steels 期刊论文
Acta Materialia, 2007, 卷号: 55, 期号: 4, 页码: 1397-1406
J. G. Li; M. Umemoto; Y. Todaka; K. Tsuchiya
收藏  |  浏览/下载：11/0  |  提交时间：2012/04/13
Research into the application of fractal geometry in characterising machined surfaces 会议论文
作者:  Jiang, ZD;  Wang, HR;  Fei, B
收藏  |  浏览/下载：2/0  |  提交时间：2020/01/07

©版权所有 ©2017 CSpace - Powered by CSpace