CORC

在结果中检索

CORC

浏览/检索结果: 共11条，第1-10条 帮助

限定条件    
已选(0)清除 条数/页：   排序方式：
AME: Attention and Memory Enhancement in Hyper-Parameter Optimization 会议论文
New Orleans, USA, 2022.6.19-6.24
作者:  Xu, Nuo;  Chang, Jianlong;  Nie, Xing;  Huo, Chunlei;  Xiang, Shiming
收藏  |  浏览/下载：17/0  |  提交时间：2022/12/20
Contingency-based Voltage Stability Monitoring via Neural Network with Multi-level Feature Fusion 会议论文
Berlin, Germany, July 11-17, 2020
作者:  Bai, Xiwei;  Tan, Jie
收藏  |  浏览/下载：10/0  |  提交时间：2020/06/12
Evaluation of a multi-level, multi-parameter detection method for digestive system cancer diagnosis. 会议论文
JOURNAL OF CLINICAL ONCOLOGY, 2015-05-20
作者:  Zhang, Yefan;  Zhao, Hong;  Bi, Xinyu;  Huang, Zhen;  Cai, Jianqiang
收藏  |  浏览/下载：6/0  |  提交时间：2020/01/04
Analysis of probability distribution of inverse problem of nonlinear model 会议论文
Progress in Electromagnetics Research Symposium, PIERS 2014, Guangzhou, China, August 25, 2014 - August 28, 2014
作者:  Tong, Xiaolin;  Wang, Zhenzhan;  Li, Qingxia
收藏  |  浏览/下载：15/0  |  提交时间：2015/09/18
Multi-kernel based feature selection for regression 会议论文
8th International Conference on Intelligent Computing (ICIC), 中国
作者:  Chao-Zhe Lin;  Xian-Kai Chen
收藏  |  浏览/下载：11/0  |  提交时间：2015/08/25
Determination of optimum process parameters in gas-assisted injection molding (EI CONFERENCE) 会议论文
2011 International Conference on Electrical Information and Mechatronics, ICEIM2011, December 23, 2011 - December 25, 2011, Jiaozuo, China
Zi K.; Chen L.
收藏  |  浏览/下载：13/0  |  提交时间：2013/03/25
With finite element analysis software Moldflow  numerical simulation and studies about FM truck roof handle were conducted on gas-assisted injection molding process. The influences of melt pre-injection shot  gas pressure  delay time and melt temperature were observed by using multi-factor orthogonal experimental method. According to the analysis of the factors' impact on evaluation index  the optimized parameter combination is obtained. Therefore the optimization design of technological parameters is done. The results show that during the gas-assisted injection molding  optimum pre-injection shot is 94%  gas pressure is 15MPa  delay time is 0.5s  melt temperature is 240 C. This study provided a more practical approach for the gas-assisted injection molding process optimization.  
Multi-Parameter Methods of Comprehensive Performance Evaluation for Aero-Engine 会议论文
1st International Conference on Intelligent System and Applied Material (GSAM 2012), Taiyuan, PEOPLES R CHINA, 2012-01-01
作者:  Yi, Hao;  Li, Wang;  Xuan, Jiang
收藏  |  浏览/下载：2/0  |  提交时间：2020/01/06
Indicator system for the pricing of wastewater reuse 会议论文
Future of Urban Wastewater Systems - Decentralisation and Reuse, Conference of the International-Water-Association (IWA), Xian, PEOPLES R CHINA, Web of Science
Song, JJ; Zhang, HT
收藏  |  浏览/下载：2/0
Novel method for the evaluation of the synchronicity of the chemomic release/dissolution of multi-component traditional Chinese medicines 会议论文
作者:  Zhang, Ji-Wen;  Chen, Li-Bing;  Gu, Jing-Kai;  Ge, Wei-Hong
收藏  |  浏览/下载：5/0  |  提交时间：2019/01/08
Multi-objective conditioning of a SVAT model for heat and CO2 fluxes prediction 会议论文
Iahs Publication
Mo X. G.; Liu S. X.; Lin Z. H.; Sun X. M.; Zhu Z. L.
收藏  |  浏览/下载：16/0  |  提交时间：2012/06/30

©版权所有 ©2017 CSpace - Powered by CSpace