3D Bio-Printing of CS/Gel/HA/Gr Hybrid Osteochondral Scaffolds | |
Hu, Xueyan1; Man, Yuan1; Li, Wenfang1; Li, Liying1; Xu, Jie1; Parungao, Roxanne4; Wang, Yiwei4; Zheng, Shuangshuang2; Nie, Yi2,3; Liu, Tianqing1 | |
刊名 | POLYMERS
![]() |
2019-10-01 | |
卷号 | 11期号:10页码:16 |
关键词 | 3d Printing Bio-ink Graphene Chitosan Gelatin Hyaluronic Acid Cartilage Repair |
DOI | 10.3390/polym11101601 |
英文摘要 | Cartilage is an important tissue contributing to the structure and function of support and protection in the human body. There are many challenges for tissue cartilage repair. However, 3D bio-printing of osteochondral scaffolds provides a promising solution. This study involved preparing bio-inks with different proportions of chitosan (Cs), Gelatin (Gel), and Hyaluronic acid (HA). The rheological properties of each bio-ink was used to identify the optimal bio-ink for printing. To improve the mechanical properties of the bio-scaffold, Graphene (GR) with a mass ratio of 0.024, 0.06, and 0.1% was doped in the bio-ink. Bio-scaffolds were prepared using 3D printing technology. The mechanical strength, water absorption rate, porosity, and degradation rate of the bio-scaffolds were compared to select the most suitable scaffold to support the proliferation and differentiation of cells. P3 Bone mesenchymal stem cells (BMSCs) were inoculated onto the bio-scaffolds to study the biocompatibility of the scaffolds. The results of SEM showed that the Cs/Gel/HA scaffolds with a GR content of 0, 0.024, 0.06, and 0.1% had a good three-dimensional porous structure and interpenetrating pores, and a porosity of more than 80%. GR was evenly distributed on the scaffold as observed by energy spectrum analyzer and polarizing microscope. With increasing GR content, the mechanical strength of the scaffold was enhanced, and pore walls became thicker and smoother. BMSCs were inoculated on the different scaffolds. The cells distributed and extended well on Cs/Gel/HA/GR scaffolds. Compared to traditional methods in tissue-engineering, this technique displays important advantages in simulating natural cartilage with the ability to finely control the mechanical and chemical properties of the scaffold to support cell distribution and proliferation for tissue repair. |
资助项目 | National Natural Science Foundation of China[31670978/31370991/21676041] ; Fok Ying Tung Education Foundation[132027] ; State Key Laboratory of Fine Chemicals[KF1111] ; Natural Science Foundation of Liaoning[20180510028] |
WOS关键词 | Articular-cartilage Defects ; Chondrogenic Differentiation ; Tissue Constructs ; Drug-delivery ; Hydrogel ; Chitosan ; Nanomaterials ; Repair ; Therapy ; Matrix |
WOS研究方向 | Polymer Science |
语种 | 英语 |
出版者 | MDPI |
WOS记录号 | WOS:000495382700070 |
资助机构 | National Natural Science Foundation of China ; Fok Ying Tung Education Foundation ; State Key Laboratory of Fine Chemicals ; Natural Science Foundation of Liaoning |
内容类型 | 期刊论文 |
源URL | [http://ir.ipe.ac.cn/handle/122111/38931] ![]() |
专题 | 中国科学院过程工程研究所 |
通讯作者 | Nie, Yi; Liu, Tianqing; Song, Kedong |
作者单位 | 1.Dalian Univ Technol, Dalian R&D Ctr Stem Cell & Tissue Engn, State Key Lab Fine Chem, Dalian 116024, Peoples R China 2.Zhengzhou Inst Emerging Ind Technol, Zhengzhou 450000, Henan, Peoples R China 3.Chinese Acad Sci, Inst Proc Engn, Key Lab Green Proc & Engn, Beijing 100190, Peoples R China 4.Univ Sydney, ANZAC Res Inst, Burns Res Grp, Concord, NSW 2139, Australia |
推荐引用方式 GB/T 7714 | Hu, Xueyan,Man, Yuan,Li, Wenfang,et al. 3D Bio-Printing of CS/Gel/HA/Gr Hybrid Osteochondral Scaffolds[J]. POLYMERS,2019,11(10):16. |
APA | Hu, Xueyan.,Man, Yuan.,Li, Wenfang.,Li, Liying.,Xu, Jie.,...&Song, Kedong.(2019).3D Bio-Printing of CS/Gel/HA/Gr Hybrid Osteochondral Scaffolds.POLYMERS,11(10),16. |
MLA | Hu, Xueyan,et al."3D Bio-Printing of CS/Gel/HA/Gr Hybrid Osteochondral Scaffolds".POLYMERS 11.10(2019):16. |
个性服务 |
查看访问统计 |
相关权益政策 |
暂无数据 |
收藏/分享 |
除非特别说明,本系统中所有内容都受版权保护,并保留所有权利。
修改评论