QQ客服 官方微博 反馈留言

	新一代超低碳贝氏体钢激光焊接热影响区的组织和性能
	赵琳 ; 陈武柱 ; 张旭东 ; ZHAO Lin ; CHEN Wu-zhu ; ZHANG Xu-dong
	2010-06-08 ; 2010-06-08
关键词	激光技术 超低碳贝氏体钢 激光焊接 热影响区 组织 韧性 laser technique ultra-low carbon bainitic steel laser welding heat-affected zone microstructure toughness TG456.7
其他题名	Microstructure and Mechanical Properties of Laser Welded Heat-Affected Zone in New Ultra-Low Carbon Bainitic Steel
中文摘要	采用激光焊接和熔化极活性气体保护焊接(MAG焊接)两种方法对800 MPa级新一代超低碳贝氏体(NULCB)钢进行了焊接,研究了焊接热影响区(HAZ)组织、性能的变化规律。实验结果表明,热影响区组织均为贝氏体板条和马氏体-奥氏体(M-A)组元组成的粒状贝氏体;在实验所采用的不同热输入情况下,随着热输入的增大,马氏体-奥氏体组元的平均宽度、总量、形状因子增大,但其线密度减少;在合适的激光焊接条件下,热影响区韧性高于母材;激光焊接接头显微硬度随热输入的增大而减小,均高于母材,未出现明显的软化区。; 800 MPa grade new ultra-low carbon bainitic(NULCB) steel was welded by laser welding and melt-active gas(MAG) welding,and the microstructure and mechanical properties of the heat-affected zone(HAZ) were investigated.The experimental results indicate that the microstructure of the HAZ is only granular bainite which consists of the bainite lath and the martensite-austenite(M-A) constituent.As the heat input that was adopted in the experiment increases,the average width,gross and shape parameter of M-A increase,but the line density decreases.The toughness of HAZ is higher than base metal under appropriate laser welding conditions.With the heat input of laser welding increase,the hardness of welded joint decreases,but it is higher than that of the base metal,indicating no softened zone appeared after laser welding.; 国家973计划(G1998061500)资助项目
语种	中文 ; 中文
内容类型	期刊论文
源URL	[http://hdl.handle.net/123456789/48000]
专题	清华大学
推荐引用方式 GB/T 7714	赵琳,陈武柱,张旭东,等. 新一代超低碳贝氏体钢激光焊接热影响区的组织和性能[J],2010, 2010.
APA	赵琳,陈武柱,张旭东,ZHAO Lin,CHEN Wu-zhu,&ZHANG Xu-dong.(2010).新一代超低碳贝氏体钢激光焊接热影响区的组织和性能..
MLA	赵琳,et al."新一代超低碳贝氏体钢激光焊接热影响区的组织和性能".(2010).

个性服务

查看访问统计

相关权益政策

暂无数据

收藏/分享

除非特别说明，本系统中所有内容都受版权保护，并保留所有权利。